{"id":2253,"date":"2019-03-29T12:14:41","date_gmt":"2019-03-29T11:14:41","guid":{"rendered":"https:\/\/slc-liftco.com\/bf-montageplatten\/"},"modified":"2024-08-19T11:28:13","modified_gmt":"2024-08-19T09:28:13","slug":"bf-adapter-plates","status":"publish","type":"page","link":"https:\/\/slc-liftco.com\/en\/safety-gear\/bf-series\/bf-adapter-plates\/","title":{"rendered":"BF Adapter plates"},"content":{"rendered":"
\n
\n\t\t\"Bremsfangvorrichtung\n\t<\/div>\n\n<\/div><\/div><\/div><\/div><\/div>
\n
\n\tHomepage<\/a><\/span><\/span>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div>
\n
\n\t

Adaptation to existing car by adapter plates<\/h1>\n<\/div>\n<\/div><\/div>
\n
\n\t

Our strength is the adaptation of our safety gears to your individual modernization task. If customized boreholes to our outer housings are not suitable for mounting the safety gear to your existing interception frame, you may succeed with adapter plates. The assembly effort on site is reduced and makes you much faster.<\/p>\n

To connect our safety gear to the car by adapter plates, we use our reinforced outer housing (SLC part number 50.100.225) for the one-piece BF safety gear and the outer housing for the tandem safety gear (SLC part number 107.060.131). Please refer to the following sketch for the dimensions of these two housings:<\/p>\n<\/div>\n<\/div><\/div><\/div>

\n
\n\t\t\t\n\t\t\t\"\"\n\t\t\t<\/a><\/div>\n\n<\/div><\/div><\/div><\/div><\/div>
\n
\n\t

When the safety gear is attached to the lower crossbar of the safety gear frame, side A of the housing is attached to the frame, and side B is used to attach the guide shoes. The adapter plates are mounted between our standard housing and the car.<\/p>\n

Connection of the adapter plate to the safety gear housing<\/h2>\n<\/div>\n<\/div><\/div><\/div>
\t\t\t

The adapter plates can be attached to the housing with three different options:<\/p>\n<\/div>\n\t\t<\/div>

\n
\n\t\t\"Checkbox\n\t<\/div>\n\n<\/div><\/div><\/div><\/div>
\n
\n\t

Fasten the plate to the SG housing with 4 x M16 countersunk screws (see section B-B (1)).<\/p>\n<\/div>\n<\/div><\/div><\/div>

\n
\n\t\t\"Checkbox\n\t<\/div>\n\n<\/div><\/div><\/div><\/div>
\n
\n\t

Plate welded<\/strong> to SG housing<\/p>\n<\/div>\n<\/div><\/div><\/div>

\n
\n\t\t\"Checkbox\n\t<\/div>\n\n<\/div><\/div><\/div><\/div>
\n
\n\t

Fasten the SG housing to the plate with 4 x M16 6KT screws (see section B-B(2)).<\/p>\n<\/div>\n<\/div><\/div><\/div>

<\/div><\/div><\/div><\/div><\/div><\/div><\/div>
\n
\n\t

The adapter plates should be at least 20mm high. The connection to the outer housing of the safety gear can be made using the existing hole pattern on the SG housing with 200mm, or 55mm hole spacing (see sketch below). With countersunk screws from above through the plate or with 6KT screws from below into threaded holes on the plate (see section B-B, top left). Alternatively, the plate can also be welded on.<\/p>\n<\/div>\n<\/div><\/div>

\n
\n\t\t\t\n\t\t\t\"\"\n\t\t\t<\/a><\/div>\n\n<\/div><\/div>
\n
\n\t

You should consider the following points when determining the mounting holes:<\/strong><\/p>\n